Hello Chalbrecht ,
I apologize for the delayed response.
There are a few options for naming the reporting output file using the sample or batch name with $(SampleName) and $(BatchFileName), but I don't see that the Sample Group is an option. You may…
Hello Achim_Hongenaert ,
I apologize for the delayed response.
There are a few outliers that can be used for recovery calculations. If this compound is added to all samples then I believe the best option will be to call it a Surrogate in quant, even…
Thank you, Linh, for your information. Given that it is an old machine, I am concerned about the potential loss of data if we upgrade the software. Instead, I will create a shutdown method to be executed at the end of the sequence run.
Hello,
I would like to ask if it is possible to execute the command "Created Compound from Each Selected Spectrum" in version B.10.0 of the Agilent MassHunter Qualitative Analysis software. This command is available in version B.07.00, but not in version…
Did you remove the diffusion pump, take it apart, empty the contents completely, wash them all with something like toluene, reassemble it with new diffusion pump fluid filled only to the top of the "cold" mark - if you didn't take it all apart and any…
Hello. Thank you howard_sanford for that answer! I talked to an Agilent technical representative and he came up with the same solution. But, we have the B.07.06.2704 version of Masshunter. What would be the data path for those files in that case? I am…
Dear juju,
Sorry to tell you, that single UV spectra extraction at a certain wavelength for each peak is not feasible within bio-SEC Software.
B rgds,
Anne
Hi,
Unfortunately, I cannot clarify the error message and the cause in this forum, so I would ask you to contact your responsible customer support. A ticket can then be opened with a detailed description including the log files so that the software…
The Digest of upcoming webinars has been updated as of June 28.
Notable additions include:
Cancer Research (1)
OMICS (1)
Check Out:
Elemental Analysis in Yeast Cells and Microplastics by ICP-MS with Automated Micro-Flow Sample Introduction…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...