Hi,
After a power cut, the batch file I had open on my desktop seems to have become damaged...
On opening the batch, it fails to open... small dialogue pops up >> "failed to open quick scan file. Failed to read binary quick scan file."
Has anyone…
Wondering if anyone has experience detecting acetic acid and formic acid using GC-FID HSS. I am trying to develop a method based on the limits described in USP <467> of 5000 ug/mL of each of the two solvents, but having a hard time seeing any peaks.
I have a gas-phase reactor system that uses the FID of a 7980A to analyze the product mixture. Currently, I have a pressure buildup (up to 30 psi - the carrier gas delivery pressure) when the system is stationary. When the gas sampling valve actuates…
Good morning,
We have an autosampler (Agilent G4567A) for our GC-FID (7820A) and the following method for cleaning and injecting samples.
I have noticed that when the syringe pumps 2µL of sample for cleaning, it then pumps quite a large volume of…
hi community we are developing a method on short chain fatty acids in plasma sample, using a DB fatwax UI column on GC-FID. we are using diethyl ether as extraction solvent however our recovery of patient samples are not so good and looking to use Isoproponol…
I have a 6890N GC with an MSD and a GC that I am trying to qualify. The MSD works fine but when it comes to the FID the units are showing as mAU and not PA so it will not pass the validation test. Does anyone have any idea on how we can change the units…
Hi, I know this is an old thread, but I am having a very similar issue. I am wondering how did you know to replace the interconnect spring rod? How did you know this was the issue, and that it was not instead an issue with the FID board or the electrometer…
I have Software Leak Test Data Wizard for VS Series Leak Detectors, but have problem to reinstall because folder Data was corrupted the file data.cab missing. Failed to install. Can anyone help without need to buy new CD Software ? withou need to buy…
I have a 6890N GC with dual FID. The back column has a much higher flow rate than the front column. The two columns are identical and the setup for inlet, column and detector are identical. I have also swapped the EPC's between the two detectors. Seems…
Hello, I would appreciate any help possible with this question. I have an Ultivo LC/TQ and it is having the problem with autotuning. It fails due to spray stability. Due to this I am thinking it might be the nebulizer? I take it out and see good spray;…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...