I met same error while installing CDS 2.7 on Win 10 pro
[3F4C:3F40][2024-03-25T11:42:54]i000: >Bootstrapper - Execute progress: 87%
[0E04:1E5C][2024-03-25T11:43:14]e000: Error 0x80071501: Process returned error: 0x1501 [0E04:1E5C][2024-03-25T11:43…
I have an Agilent 7890A with a split/splitless injector and FID. The FID has been experiencing a falling baseline signal that triggers the instrument to relight the flame unless I lower the lit offset value. As it gets worse, I have to set the lit offset…
HP 5890 II not responding. After power-up, initiates "Passed Self Test" routine but stalls at that point. The oven works, and FID is ignited but the light by "Not Ready" is lit up. ChemStation program states: "GC Not Found. Check that GC is Correctly…
Hi, I am wondering if the FID detector requires nitrogen make up flow while in standby mode or is it sufficient to have the FID idle at a temperature above 100 to protect it in downtime.
Thanks.
Hi all, we have Error "1467: Option gas flow rate is out of acceptable range" when trying to ignite the plasma. But the thing is, we don't use option gas (we are running in laser ablation mode) and have nothing connected. We think it might be related…
I use a 8890 series GC with MSD, FID, TCD. Splitter from column to MSD & TCD or FID Multimode Inlet. 30m DB-5 Column. MMI 325C, FID 325C. 10 C/min ramp until 325 and hold for 15 min. 45 min run time It's 98% used for QC using TCD & MS. However there is…
Hello
I wish if i can find solution the this problem
I don't have access to ignite plasma because after i turn on chiller ( Temperature the peltier it ouside range -40 ± 2 )
some times take -52 C or more .... ( i notice there are not value exact…
Hi, Have this issue with an Agilent 6850 GC: The system performs normally during the pre-run: the oven temperature, front inlet total flow/inlet pressure and signal 1 valve values are all normal/stable. When we switch to the test method and start sample…
Additionally, the detector will not light regardless of whether the column is installed or not. I can hear an ignition happening but the detector fails to stay lit every time.
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...