Dear all, I have a question for GCMS. I would like to know how to select the chemical name of a substance that I search from a search using NIST program into the selected MS spectrum and I need to know any trick of how to search the library very fast…
No. There is a QTOF specific collision cell EPC module. The software needs to recognize it.
G3850-60039 | Agilent EPC module
G3470-60550 | Agilent , Fitting and 1/16" tubing to go from the EPC module to the QTOF CC 1/16" Swagelok connection.
Is…
Durjoy123 would you please start a new forum post with your questions? Please include as much useful information as possible - instrument model number and age of the system, MassHunter Acquisition software version, which high vacuum pump type, the vacuum…
Hello,
I am going to move this post to the GC forum as they will have a better chance of helping. I assume you want to know how to change the front panel language to some other language.
Marty
Hi Kenforce,
In this case, I would run the pressure decay test, as you could have a small leak that is causing the inconsistency. I would also consider increasing your oven equilibration time by a 0.5min or so, just to ensure the column phase is at…
Hi Marty,
We have a FID and an MS connected to the same system. We only want to acquire the signal of FID, but if we want to report the method parameters we are “forced” to acquire both (we do not really know why and we have already ask the question…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...