I would like to install Agilent MassHunter Qualitative Analysis B.07.00 and Agilent MassHunter Quantitative Analysis B.08.00 onto my Microsoft Surface Pro 6 (Windows 10) to view results from my headspace samples using GCMS. I have tried installing the…
I am attempting to run the amino acid analysis protocol from the Woodward and Henderson paper "High-Speed Amino Acid Analysis (AAA) on 1.8 µM Reversed-Phase (RP) Columns" ( https://www.agilent.com/cs/library/Support/Documents/5989-6297EN.pdf ), but receive…
Hi Avrom, Below are the release notes for the new driver. New drivers are released periodically to allow us to use new equipment without having to upgrade a complete software package each time. The new driver has some enhancements for the older systems…
Hello, we are using 7700X series ICP-MS until 2014 . A few days ago we had an error message (Error 1118) . When our instrument is changing from Standby mode to Analysis mode vacuum pressure (IF/BK) can not drop below the lower limit within the prescribed…
We normally use BFB Autotune. BFB Target Tune also fails with the default settings. The filaments are both new and both act the same. When I cleaned the source I found the lens insulator was cracked so that was replaced. Dynamically ramping the entrance…
Hi everyone. There are some doubts that I would like to clarify because we're experiencing some drift and sensitivity problems and it may help.
We've already cleaned the cones, lenses and sample introduction system, including the torch.
1) There is…
Hello,
I cannot tell what ECM or CDS version you are using and that can make a difference in the search capabilities. Take a look at the attached guide on page 50 for information on searching with ECM 3.x and CDS 2.x. You are not extracting any…
This presentation shows basic information, maintenance procedures, and exhaust venting for the three possible rough pumps used on Agilent single quad GC/MS systems.
Rough Pumps on Agilent 5977x GCMS systems May 2021 rev2.pdf
This Information Applies To: Agilent GC systems with Gas Clean Filter
Issue
If you have determined that the Gas Clean Filter is saturated, it mus be replaced (see the article When to Replace the Gas Clean Carrier Gas Filter ).
The steps described...
This Information Applies To: Agilent GC Systems 8890/8860/Intuvo 9000 /7890/7820/6850/6890
Issue
General guidance on GC column flow rates, outlining the correct column flow rate for optimal compound separation depends on the column internal diameter...
This Information Applies To: Agilent GC Method Translator
Issue
Detailed instructions on translating methods using the GC Method Translator.
Background
For ideal use of cases and applications with the GC Method Translator, see the article...
This Information Applies To: Agilent Solvent Vent Calculator
Issue
The Solvent Vent Calculator estimates the Agilent solvent vapor exit (SVE) accessory valve timing based on solvent type, oven temperature, vent flow, and pressure.
Background...
This Information Applies To: Use of the Agilent GC Method Translator
Issue
How to correctly use the GC Method Translator to convert a method to suit a different GC configuration or to optimize a method.
Background
The GC Method Translator...
This Information Applies To: GC Pressure Flow Calculator
Issue
Instructions for the correct use of the Pressure Flow Calculator.
Background
The Pressure Flow Calculator uses the column dimensions, oven temperature, and detector outlet pressure...
This Information Applies To: The Agilent GC Vapor Volume Calculator.
Issue
The Vapor Volume Calculator determines the vapor volume based on the injection volume, solvent type, inlet head pressure, and the inlet temperature. This calculated vapor...
This Information Applies To: Agilent GCs
Issue
Agilent provides free GC calculators and tools to assist with method development.
Background
Tips : The calculators are available for downloading at Agilent.com .
Vapor Volume...
This Information Applies To: Agilent GC Systems
Issue
The Agilent Gas Clean Carrier Gas Filter delivers faster stabilization times for increased GC productivity, removes oxygen, moisture, and hydrocarbons from the carrier gas for MS applications...
This Information Applies To: Agilent GC systems
Issue
When a GC heater cannot reach setpoint, or taking too long to reach setpoint, the GC will enter a "Thermal Shutdown" (or similar heater error) state to protect itself. This state will turn off...