Can you import a compound list from excel to Optimizer in MH12.1? Inside the software, I do not see where to add the position of each compound in the autosampler.
Hello mtmail00
You can configure HPLC from Tool Tab--> Settings--> Hardware--> Sample Instroduction
In Sample introduction you can select " Agilent 1200 LC", after this , auto config pop up appears to type the HPLC IP
Thanks
Regards
Hello! Good morning
Instrument: GCMSMS 7890B (G3445B)
Acquisition Software: MassHunter Workstation GC/MS Data Acquisition Version 10.0 Service Release 1, Build 10.0.384.1
Since last week we've been experiencing one of our instruments randomly stopping…
If it's just over the weekend, I would turn the flame off but keep some flow through the columns. Best to keep the inlet at a minimum of 5 psig and 20 mL/min flow. There are some suggestions in the 8890 Operation manual also: Operation Manual (agilent…
Thank you very much for your reply
Regarding the software error, a complete software reset is usually performed when starting the analysis routine, however, according to your instructions, it was done again, but the error continues.
When the error…
This potential electronics problem is beyond the scope of this forum. The best thing to do is to contact your local Agilent service and start the process of an onsite service call.
Turbomolecular pumps do not have any maintenance procedures. They typically run forever and then don't start back up again after being stopped. Has the problem continued to happen?
The only rough pumps supported by Agilent that should be plugged into the QQQ systems are the Agilent IDP-10 and the Edwards RV-5. Those are the only tested and supported pumps and the only ones used for Agilent service calls. If the MS40-S has the same…
This Information Applies To: Agilent GC systems with Gas Clean Filter
Issue
If you have determined that the Gas Clean Filter is saturated, it mus be replaced (see the article When to Replace the Gas Clean Carrier Gas Filter ).
The steps described...
This Information Applies To: Agilent GC Systems 8890/8860/Intuvo 9000 /7890/7820/6850/6890
Issue
General guidance on GC column flow rates, outlining the correct column flow rate for optimal compound separation depends on the column internal diameter...
This Information Applies To: Agilent GC Method Translator
Issue
Detailed instructions on translating methods using the GC Method Translator.
Background
For ideal use of cases and applications with the GC Method Translator, see the article...
This Information Applies To: Agilent Solvent Vent Calculator
Issue
The Solvent Vent Calculator estimates the Agilent solvent vapor exit (SVE) accessory valve timing based on solvent type, oven temperature, vent flow, and pressure.
Background...
This Information Applies To: Use of the Agilent GC Method Translator
Issue
How to correctly use the GC Method Translator to convert a method to suit a different GC configuration or to optimize a method.
Background
The GC Method Translator...
This Information Applies To: GC Pressure Flow Calculator
Issue
Instructions for the correct use of the Pressure Flow Calculator.
Background
The Pressure Flow Calculator uses the column dimensions, oven temperature, and detector outlet pressure...
This Information Applies To: The Agilent GC Vapor Volume Calculator.
Issue
The Vapor Volume Calculator determines the vapor volume based on the injection volume, solvent type, inlet head pressure, and the inlet temperature. This calculated vapor...
This Information Applies To: Agilent GCs
Issue
Agilent provides free GC calculators and tools to assist with method development.
Background
Tips : The calculators are available for downloading at Agilent.com .
Vapor Volume...
This Information Applies To: Agilent GC Systems
Issue
The Agilent Gas Clean Carrier Gas Filter delivers faster stabilization times for increased GC productivity, removes oxygen, moisture, and hydrocarbons from the carrier gas for MS applications...
This Information Applies To: Agilent GC systems
Issue
When a GC heater cannot reach setpoint, or taking too long to reach setpoint, the GC will enter a "Thermal Shutdown" (or similar heater error) state to protect itself. This state will turn off...