I met same error while installing CDS 2.7 on Win 10 pro
[3F4C:3F40][2024-03-25T11:42:54]i000: >Bootstrapper - Execute progress: 87%
[0E04:1E5C][2024-03-25T11:43:14]e000: Error 0x80071501: Process returned error: 0x1501 [0E04:1E5C][2024-03-25T11:43…
I have an Agilent 7890A with a split/splitless injector and FID. The FID has been experiencing a falling baseline signal that triggers the instrument to relight the flame unless I lower the lit offset value. As it gets worse, I have to set the lit offset…
HP 5890 II not responding. After power-up, initiates "Passed Self Test" routine but stalls at that point. The oven works, and FID is ignited but the light by "Not Ready" is lit up. ChemStation program states: "GC Not Found. Check that GC is Correctly…
Hi all, we have Error "1467: Option gas flow rate is out of acceptable range" when trying to ignite the plasma. But the thing is, we don't use option gas (we are running in laser ablation mode) and have nothing connected. We think it might be related…
Hi, I am wondering if the FID detector requires nitrogen make up flow while in standby mode or is it sufficient to have the FID idle at a temperature above 100 to protect it in downtime.
Thanks.
Hello
I wish if i can find solution the this problem
I don't have access to ignite plasma because after i turn on chiller ( Temperature the peltier it ouside range -40 ± 2 )
some times take -52 C or more .... ( i notice there are not value exact…
Hi, Have this issue with an Agilent 6850 GC: The system performs normally during the pre-run: the oven temperature, front inlet total flow/inlet pressure and signal 1 valve values are all normal/stable. When we switch to the test method and start sample…
I use a 8890 series GC with MSD, FID, TCD. Splitter from column to MSD & TCD or FID Multimode Inlet. 30m DB-5 Column. MMI 325C, FID 325C. 10 C/min ramp until 325 and hold for 15 min. 45 min run time It's 98% used for QC using TCD & MS. However there is…
Additionally, the detector will not light regardless of whether the column is installed or not. I can hear an ignition happening but the detector fails to stay lit every time.
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900) with ICP Expert 7.5.x Software
Issue
The Recommended Routine Maintenance Schedule does not adjust for the number of samples analyses or the sample matrix, both of which...
This Information Applies To: Agilent 7890/7820 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent LC pumps
Issue:
Stuck or obstructed check valves (Active Inlet Valve (AIV), Passive Inlet Valve (PIV), Outlet Ball Valve (OBV)) can cause issues such as no-flow or no-pressure, moderate to strong drops in pressure...
This Information Applies To: Agilent 1260 Infinity II multisampler, 1290 Infinity II multisampler, 1260 Infinity II SFC multisampler, and 1260 Infinity II bio-Inert multisampler
Issue
The needle bends while moving to the wash port or showing one...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the step-by-step instruction on how to overlay chromatograms for OpenLab CDS 2.x
Steps to Follow
Load data from result sets or single samples. See Load or add...
This Information Applies To: Agilent Lab Advisor Software, Agilent Multicolumn Thermostat
Issue:
Agilent Lab Advisor is a great tool to diagnose the issue of your HPLC. Running the tests that are relevant to your specific issue in the Service &...
This Information Applies To: Agilent OpenLab CDS (ver 2.x)
Content:
The following procedure shows how to review completed injections in a running sequence in OpenLab CDS (ver 2.x).
Steps to Follow:
Select the sequence from the Run Queue...