Agilent Community
Agilent Community
  • User
  • Site
  • Search the Community
  • User
  • Home
  • Technical Areas
    Technical Areas
    • AssayMap
    • Atomic Spectroscopy
    • Automated Electrophoresis
    • Bioreagents
    • Cell Analysis
    • Consumables
    • CrossLab Connect
      CrossLab Connect
      • Service Management
      • Smart Alerts
    • Dissolution
    • GC
    • GC/MS
    • LC/MS
    • LC
    • Molecular Spectroscopy
      Molecular Spectroscopy
      • Molecular Spectroscopy - UV-Vis & UV-Vis-NIR, FTIR, Raman & Fluorescence
      • 8700 LDIR User Group
    • Sample Preparation
    • Software
      Software
      • Chromatography Software
        OpenLab CDS, OpenLab ChemStation, OpenLab EZChrom
      • Data Management Software
        OpenLab ECM, OpenLab ECM XT, OpenLab Server
      • Mass Spectrometry Software
        Data Analysis, Data Acquisition, Productivity App, WalkUp Software
    • Vacuum
  • Applications Areas
    Applications Areas
    • Basic Research
    • Energy and Chemicals
    • Environmental
    • Food and Agriculture
  • Agilent Knowledge Portal
  • Links
    Links
    • Collection of Support Resources
    • Webinar Notifications
    • Contact Support
    • User Contributions
  • Getting Started
    Community Help and Resources
  • Browse
    Browse
    • People
    • Places
    • Your View
    • Your Community Inbox
Molecular Spectroscopy
  • Technical Areas
Molecular Spectroscopy
Wiki Cary UV Workstation Data Analysis FAQs
  • Announcements
  • Blog
  • Forum
  • Wiki
  • More
  • Cancel
Actions
  • Share
  • More
  • Cancel
Table of Contents
  • -Molecular Spectroscopy Support, Applications & eLearning Resources
    • -UV-Vis & UV-Vis-NIR Spectroscopy Resources
      • -Cary 3500 FAQs
        • Cary 3500 General Operation FAQs
        • Migration from Cary WinUV or UV ChemStation Software Comparison Tool
        • Cary UV Workstation Data Analysis FAQs
        • Cary UV Workstation Method Development FAQs
        • Cary 3500 UV-Vis Sample Temperature Probe FAQs
    • FTIR Spectroscopy Resources
    • Raman Spectroscopy Resources
    • Fluorescence Spectroscopy Resources
    • LDIR Chemical Imaging Spectroscopy Resources
Still Need Help?

Post your question in our User Forum or Contact Support.

Cary UV Workstation Data Analysis FAQs

Created by Agilent Agilent over 2 years ago | Last modified by kristen.sensabaugh kristen.sensabaugh over 2 years ago

Baseline correction: is there a way to add a baseline correction before analysis, or must it be done after the fact via calculator? 

You can perform a baseline before your sample scan, the option is available on the “Sequencer” page. You can also apply a sloping baseline via the calculator tool after sample scans.

 

How do I delete extra graphs once I’ve selected “add graph”?

If you hover your mouse over the graph, there is a toolbar in the upper right corner of the graph. Select the three vertical dots. At the bottom of that drop down, select the “remove graph” option. If you are using a laptop, or have multiple graphs you may need to scroll down the menu to access it.

 

Is there any way to pull up the calculator other than “Ctrl/click” – i.e. – is it in a menu somewhere?

The calculator will only appear if one or more traces is selected. The primary way to start this is to hold control and click the trace of interest. An alternative would be to click “select all traces” from the graph toolbar menu, then it will appear.

 

Can I delete a result table, once added to the report?

There is no way to remove a result table once it is present on a report. From version 1.1, result tables can be deleted while hovering over the table title.

 

In kinetics mode, I see no option to start the calculator button, is this possible?

The calculator button feature is only available in the “Scan application”. The other applications have specific calculations, e.g. Kinetics has rate calculations. These applications can be performed on kinetics wavelength collects or sliced traces from scanning kinetics data. By selecting the “rate calculations” card, inputting desired time range etc. then selecting recalculate it will generate a rate calculation table

 

More FAQs: Cary 3500 FAQs

 

Keywords: Cary 3500 UV-Vis Spectrophotometer, UV-Vis, simultaneous scanning, temperature controlled UV-Vis, Compact UV-Vis, Compact Peltier UV-Vis, Multicell UV-Vis, Multicell Peltier UV-Vis, Multizone UV-Vis system, Cary UV Workstation.

  • cary 3500
  • cary uv workstation
  • multicell peltier uv-vis
  • compact peltier uv-vis
  • uv-vis
  • UV-Vis and UV-Vis-NIR
  • temperature controlled uv-vis
  • simultaneous scanning
  • cary 3500 uv-vis spectrophotometer
  • multizone uv-vis system
  • multicell uv-vis
  • compact uv-vis
  • faq
  • Share
  • History
  • More
  • Cancel
  • Sign in to reply
  • Agilent
    Agilent over 2 years ago in reply to arjun

    Hi Arjun,

    Thanks for the question! Unfortunately there is not currently a way to set the trace colours in Cary UV Workstation. This is something we will look to implement in the near future.

     

    Best regards,

    Matt

    • Cancel
    • Vote Up 0 Vote Down
    • Sign in to reply
    • More
    • Cancel
  • arjun
    arjun over 2 years ago

    ; usually Scan spectrum/graph comes in colors, is there any mode or way to make  single scan as normal Black or Blue color scan lines. or this feature is available in upcoming software release in mid july. 

    pls confirm ? 

    • Cancel
    • Vote Up 0 Vote Down
    • Sign in to reply
    • More
    • Cancel
Was this helpful?
  • Yes
  • No
Thank you for your feedback!

Agilent Community Feedback

Agilent Community Feedback

×
We are glad this was helpful! We are sorry this was not helpful. If you still need assistance please create a community post or contact support. To help us improve, please provide any additional feedback. For full details of how we will treat your information, please view our privacy policy.
Submit Cancel
Submit Cancel
Related
Privacy Statement
Terms of Use
Contact Us
Site Help