7683 Series ALS on 6890N GC won't inject

Hello behringerd,

Could you provide a firmware of the instrument and the revision of Ezchrom? You can find the revision of Ezchrom from the help>about menu in the interface and the firmware you can find from the front panel of the instrument by clicking options then scroll to diagnostics and click enter then scroll to instrument status and press enter. Then from that menu there are firmware listed for the GC, which is listed as "version" and also a firmware version for the sampler and injector. Thank you

GC firmware is A.03.08.  Sampler firmware is G2612A.01.04.  Front Inj. Firmware is G2613A.10.07.

The EZChrom Rev. is A.04.07.

The tray model number is G2614A.

[personal information removed by moderator]

You mentioned that you tried a different sampler on the GC and got the same error message from Ezchrom and that's why you believe it is a board issue. You can verify that by running a method from the front panel of the instrument. If the instrument is able to complete a run from the front panel with no errors, then it may be a problem with the software. If the GC can't complete a run, then it is a board issue and onsite is required. Please see the attached document on how to run a front panel method on a 6890.

Note that where the procedure asks to enter a number for "samples", you should enter a larger vial position (i.e. sample 30 for vial position 30) so that the vial is taken from the sampler and not the injector. Also, be sure to have the software closed so the instrument isn't controlled by anything else.

The instrument was able to complete a run from the front panel with no errors.

I dont know the EZchrom software, but other platforms do not use external, is there an option for GC/ALS for the source in the method?

James

The plastics may have been changed at some point. A.03.08 firmware is a 6890A or 6890 Plus model. If the samplers plug into the back of the GC on a separate sampler board you have the 6890 plus.The lan card would also be separate from the main board

If the instrument injects ok from the front panel, and if that indicates a problem with the software, what could that problem be?  We have verified that the information in the method is correct.

[Personal Information Removed by Moderator]

Are you able to post a screenshot of the error message? It could be helpful.

By the way, with a firmware revision of A.03.08, the GC is either a 6890A or 6890 Plus, not a 6890N. You have a separate box that is the sampler controller, right? In the 6890N, the injectors and tray plug directly into the back of the GC.

I agree that it doesn't seem likely that there is a hardware problem if the instrument can make a run from the front panel.

Are you able to post a screenshot of the error message? It could be helpful.

By the way, with a firmware revision of A.03.08, the GC is either a 6890A or 6890 Plus, not a 6890N. You have a separate box that is the sampler controller, right? In the 6890N, the injectors and tray plug directly into the back of the GC.

I agree that it doesn't seem likely that there is a hardware problem if the instrument can make a run from the front panel.

The plastics may have been changed at some point. A.03.08 firmware is a 6890A or 6890 Plus model. If the samplers plug into the back of the GC on a separate sampler board you have the 6890 plus.The lan card would also be separate from the main board

The injectors and tray do plug directly into the back of the GC.  It says “6890N” on the front.  There is no controller box with this GC.

I will attempt to get a screen shot of the error message.

[Personal Information Removed by Moderator]

Another critical piece of information would be whether you configured your instrument type as "Classic Agilent 6890 GC" or "Agilent 6890 GC". They use completely different GC control software.

It’s configured as “Agilent 6890 GC”.

[Personal Information Removed by Moderator]