Hello,
I have a question about our GC 8860, which has been experiencing some problems since I changed the valve pressure.
Although it works well immediately after the change, if I don't use the GC for a few days, the first few runs produce larger…
Hello, Our lab has a GC-MS (7890B/5977B) system which uses MassHunter version B.07.01 SP1. We recently installed a FID on the system to run FID analysis separate from the MS. We are finding that MassHunter is not as suitable to use for FID analysis in…
I have an agilent GC-FID 6890 i use for TPH and PAH of soil samples yet i want to calibrate it for Oxygenates in gasoline and Aromatics don't know how to go about it
If you receive an onscreen notification to contact Agilent for your service or support request, please do so. Some instruments cannot have service tickets generated through the CrossLab Connect software.
If you receive an email that your service ticket…
Hi joonseok
Put the samples in a separate sequence to the wash runs. In the sequence parameters for the samples, select the post sequence option to switch off the lamps. Run the sample sequence and queue up the wash sequence from the Run control menu…
The mass calibration/check for the quadrupole is failing across all isolation widths. Mass delta on 322m/z exceeds limits.
We system tuned a few weeks ago. Can someone please outline the troubleshooting workflow for this type of issue (where to start…
Hi All, I need help to fix either baseline drifted down or change volume injection of water samples in GC/FID. Specifically, I am setting up a new GC instrument for analysis of methanol and alcohols in water samples with the following conditions: - Instrument…
Hi all,
I have been trying to change our 8890 GC carrier gas with a FID from helium to nitrogen. To verify the change went well I first prepared a test mixture of lab solvents (methanol, acetone, pentane, dcm, isopropanol), ran it using He, then ran…
A follow up question about this, if it ever occurs again. When the instrument errored out it prevented us from even initializing the instrument properly. Is it possible to auto reference even if the unit failed to initialize correctly?
Hi Paul,
Thanks for the response. We are using Agilent 5183-4702 liner, HP-5ms Ultra Inert Columns (Part Number:19091S-433UI, 30 m, 0.25 mm, 0.25 µm, 7 inch cage).
We are running in Scan, absolute. I always use autotune, I didn't find a place to choose…
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue
Early Maintenance Feedback is a useful feature on Agilent GC Systems and software that allows a user to monitor the maintenance needed on their GC. This feature allows for users to...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue:
This procedure outlines the steps to view and clear the maintenance warnings on based on Agilent 8890/8860 GCs. You can also follow the onscreen instructions to perform maintenance...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with Agilent MS-40+ rotary vane pump.
Issue
Regular check of the rough pump fluid level in your MS40+ pump as part of regular 6000 LC/MS system maintenance checks.
Steps...
This Information Applies To the Following Products : All Agilent iFunnel and Agilent Jet Stream (AJS) 6400 Series LC/MS triple quadrupole systems, Agilent 6460A/C, 6470A, 6490A, and 6495A/B/C
Issue:
As LC Triple Quadrupole Mass Spectrometers (LC...