Hi James,
I am having sort of similar issue as nbrow12 has had 4 years ago. My system is a 7890A GC. I am getting PCM C flow shut down. I did a leak check around inlet, no leak was detected. I can not find out solution on my own. Please advise. Thanks…
The Digest of upcoming webinars has been updated as of July 8.
Notable additions include:
BioPharma (2)
Pharma (1)
Check Out:
Elemental Analysis in Yeast Cells and Microplastics by ICP-MS with Automated Micro-Flow Sample Introduction on…
Instrument tests were only part of Chemstation until version A.10.02 (ages ago). Tests, calibrations etc. are now run from the LabAdvisor software. Alternatively certain tests are available from the handheld controllers, such as the Instant Pilot G4208A…
Do you have any macros set to load in the user.mac file? Whenever I had an issue like this, it's because one of the macros loaded at startup had a syntax error in it.
Is there any tool for SPS 3 autosampler calibration? I am trying to calibrate an SPS 3 to use it with a ICP-OES 5110 but I didn't found anything like SPS 4 Wizard Calibration.
Even though SPS 4 Wizard Calibration conects with the SPS 3 by serial port…
This Information Applies To: 1100, 1200 and 1260 Infinity I and 1260 Infinity II LC Pumps (Excluding preparative pumps with electromagnetic purge valve (EMPV): G1361A. Not applicable to any of the 1290 Infinity II modules with automatic purge valve: G4220X...
This Information Applies To: Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules
Issue:
Removing and re-installing Visible and UV lamps in Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules.
Both the visible and UV lamps are consumable...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pumps.
Issue:
Removal of the pump head from the pump metering drive for maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Module.
Steps...
This Information Applies To: All Agilent 1260 Infinity Binary, Quaternary, or Isocratic Pumps without the Seal Wash Option installed.
Issue:
Worn pump seals can shed small particles that can cause blockages and pressure issues downstream of the...
This Information Applies To: Agilent G7167x Multisampler modules
Issue:
Required when:
The needle seat is visibly damaged, blocked, or is leaking.
Leaks or blockages in the Vialsampler are observed, especially between the needle and needle...
This Information Applies To: Agilent 1260 Isocratic (G1310B) Quaternary (G1311B) Pumps.
Issue
Required when:
The inlet valve is defective.
The pressure or leak test in Lab Advisor suggests the inlet valve may require replacement.
A large...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
Required when:
The outlet valve is defective or leaking.
The pressure or leak test in Lab Advisor suggests the outlet valve may require replacement...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
The seal wear in procedure is important as it acts to "bed-in" the seals to ensure a leak free and pressure-tight pump head.
Required when:...
This Information Applies To: Agilent G7167A/B Infinity II Multisamplers
Issue:
The Agilent Multisampler autoreferencing procedure uses predefined positions on the base plate and the sample hotel to calibrate the positioning of the needle parkstation...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Modules
Issue:
Reinstallation of the pump head on the pump metering drive during maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump...