I have a 5890 GC running ASTM D2887, simulated distillation. It is equipped with a FID and recently we noticed the FID won't light. Flows are good and gases are good. Looking at the setpoint/actual reading, it states it is at the correct temperature …
I completed the inlet leak test and it passed and I also completed the FID jet restriction test and it passed. Yet, when I compare scans on the 8890 the peaks shift more compared to the same injections on my 6890. Does anyone have any thought on this…
I appreciate your answering my post!
I tried launching in the Control Panel, with the correct project selected. I also tried to launch MH12.1 using a desktop shortcut made for that project.
I'm sorry, I'm not sure what ESW/FW refers to, could you…
Adding to this post,
I've tried creating a virtual instrument to check if is a problem with the hplc, Aquisition still is not opening for the virtual device.
the acquisition logo stops at initializing modules, turns black and then crashes.
Hello DET ,
Sorry for the late response on this.
What sort of spiking do you see usually? What is the output of the FID, in pA?
Are you using any UPS systems, or are the GCs plugged directly into the wall?
Our customer got an error, "Failed to connect to an IPC Port: The system cannot find the file specified." from MassHunter.
Do you know any cause of this message? There was no record of this message in the diagnostic log files.
during installation of NEW FLD Detector it started to show error Excitation Motor didn't find its position then gives error Excitation motor has failed and last error it still showing up is Exciation endcoder index failed to calculate so what do you think…
I am getting an error on our Agilent 1290/6420 LC-MS/MS. I start a run and the first injection is successful, then when it goes to the second injection, it errors and says "failed switching to main pass" and shuts down. From my reading, this is a failure…
This Information Applies To: Agilent CI Source
Issue:
During normal operation of the GC/MS, the CI ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or routine replacement of consumable parts (filament and...
This Information Applies To: Agilent OpenLab CDS
Issue
This article will explain how to add a sequence summary report line to a sequence, in Agilent OpenLab CDS, as well as how to configure it so it matches your reporting needs.
Background ...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS ChemStation, OpenLab CDS EZChrom.
Issue
Process for creating a desktop shortcut for your instruments, with OpenLab software, to enable quick access to your acquisition window.
Background...
This Information Applies To: Agilent LC Systems
Issue
Agilent modules will go into an error status (red status light) when an error condition specific to that module occurs. For example, metering home failed will be specific for the autosampler...
This Information Applies To: Agilent Analytical LC Autosamplers
Issue
To increase the maximum injection volume of an autosampler, there are two ways to do it. While both will provide larger injection volumes, there are advantages and disadvantages...
How to Recover a SubscribeNet Password
Multiple Results
This Information Applies To: Agilent Software products with SubscribeNet license.
Issue
Resolutions for password recovery use if you have: lost your password, been locked out of the account, or you don't know if you have an account with SubscribeNet...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS EZChrom
Issue
Steps to create a Data Analysis shortcut for one or more of your Projects defined in the OpenLab Control Panel .
Steps to Follow
Open the Control Panel of your...
This Information Applies To: Agilent 6100, 6200, 6400 and 6500 LC/MS Systems
Issue
Error on the Mainboard reporting “Leak Detected”.
Background
The fault “Mainboard #1: Leak Detected” is reported in the Data Acquisition Software Logs ( Figure...
This Information Applies To: Agilent LC/MS Systems
Issue
The MS solvent selection valve (SSV) rotor seal is replaced annually as part of the Preventive Maintenance. It can also be replaced as part of troubleshooting a leak, a flow blockage, or when...
This Information Applies To: All Agilent HPLC modules.
Issue:
The firmware is stored on a HPLC module's mainboard. It's a set of parameters, low-level commands, and functions stored on the internal memory of a HPLC module and required for its operation...