I guess checking the settings will be the first thing. On the GC side, since RT did not shift too much, I think oven temp would be of a less issue. But flow and pressure might act more in this case. Based on info I learnt from here, both pressure and…
Hello AJohnson13 ,
Lab Advisor can be currently downloaded from this page.
Lab Advisor Software Download | Agilent
This may change over time. You can search the web for 'agilent lab advisor download' to find a link to the current download location…
Hello,
So, you should be able to add another column to your report table and change the value to = Compound_Concentration * Sample_Amount / 100 to remove the sample amount and percentage. If you need to remove a multiplier or dilution you will need…
Hello,
LIMS ID is not available as a token for sample name, datafile name, or in CDS DA for report output. You can see the options in the screenshot below. It can be a value in the CSV file but not used in the name. The only other option would be…
Our G4220A (1290 Bin Pump) is setup to work with the seal wash currently. It operates with our instrument with no issue. If I go into the instrument configuration and check the box to enable the pump seal wash (The pump is installed), it will lose connection…
Hi RDP0314,
One thing to check is the injection settings. This behavior is common when the GC is expecting a series of manual injections. To check, click on the Instrument menu shown on your screen capture above and 'Select Injection Source' or similar…
This Information Applies To: Agilent CI Source
Issue:
During normal operation of the GC/MS, the CI ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or routine replacement of consumable parts (filament and...
This Information Applies To: Agilent OpenLab CDS
Issue
This article will explain how to add a sequence summary report line to a sequence, in Agilent OpenLab CDS, as well as how to configure it so it matches your reporting needs.
Background ...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS ChemStation, OpenLab CDS EZChrom.
Issue
Process for creating a desktop shortcut for your instruments, with OpenLab software, to enable quick access to your acquisition window.
Background...
This Information Applies To: Agilent LC Systems
Issue
Agilent modules will go into an error status (red status light) when an error condition specific to that module occurs. For example, metering home failed will be specific for the autosampler...
This Information Applies To: Agilent Analytical LC Autosamplers
Issue
To increase the maximum injection volume of an autosampler, there are two ways to do it. While both will provide larger injection volumes, there are advantages and disadvantages...
How to Recover a SubscribeNet Password
Multiple Results
This Information Applies To: Agilent Software products with SubscribeNet license.
Issue
Resolutions for password recovery use if you have: lost your password, been locked out of the account, or you don't know if you have an account with SubscribeNet...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS EZChrom
Issue
Steps to create a Data Analysis shortcut for one or more of your Projects defined in the OpenLab Control Panel .
Steps to Follow
Open the Control Panel of your...
This Information Applies To: Agilent 6100, 6200, 6400 and 6500 LC/MS Systems
Issue
Error on the Mainboard reporting “Leak Detected”.
Background
The fault “Mainboard #1: Leak Detected” is reported in the Data Acquisition Software Logs ( Figure...
This Information Applies To: Agilent LC/MS Systems
Issue
The MS solvent selection valve (SSV) rotor seal is replaced annually as part of the Preventive Maintenance. It can also be replaced as part of troubleshooting a leak, a flow blockage, or when...
This Information Applies To: All Agilent HPLC modules.
Issue:
The firmware is stored on a HPLC module's mainboard. It's a set of parameters, low-level commands, and functions stored on the internal memory of a HPLC module and required for its operation...