How do I convert the Peak Area (pA*s) measurements in a GC-FID lab report into mass/weight percent of components for analysed crude oil samples?
How do I characterise the n-paraffins and estimate the single carbon number (SCN) distribution from the…
Hi all :) For he experts here! I did my yearly maintenance (new gold seal, liner, column end cut to inlet and FID, new gas filters, ...). But since then, everytime there's a temperature change in the GC, the signal will show a sudden bump and then it…
Hello MikeL ,
Just wanted to post what we discussed during your call with the support center so if anyone else sees a similar problem they will have some things to try.
There can be issues with copying and pasting fairly large amounts of information…
I'm running a GC(7890A) / MS(5975C) with MassHunter Acquisition software. I automate much of my data analysis in Python by exporting the GC signal (FID) to .csv, and then exporting the MS signal using 'Export 3-D Data...' in MSD Productivity Chemstation…
i had faced this troubleshooting before
it is probably a software problem.
first close masshunter and double click ( remove masshunter process)
open the soft again and try to create another method with same parameters it should work
also try to…
Recently, we connected the column (CP7429) to TCD and FID using a Y splitter. However, there is no signal response on both TCD and FID after manually injection of the calibration gas (containing H2, CO, CH4, C2H4, C2H6 in CO2). The carrier gas is Ar.…
When performing the Eukariote Total RNA test on the same chip we had some samples with very degraded RNA and one sample with what seems like good quality RNA but the software failed to give a RIN value for that sample. Is there a way to still measure…
Dear Colleagues, apologizing for frequently wondering but I first faced this problem. GC produces a signal without turning on the FID Detector!? Please look at the attached photo. After turning on the detector and then conditioning the column while the…
For many FID methods, 10-20 Hz data rate is sufficient unless you're doing a fast method of some sort. You need enough data points to define the peak correctly and not get any spectral tilt. Typically 15-20 points across the peak is enough.
Hello AGILENT family,
i have a few questions on the analysis of Pb in blood samples.
am failing to get the right concentrations of the QC sample 8ppb instead it’s reading 0.08 ppb and at the same time it’s also showing overange (0.08o) even when my…
This Information Applies To: Agilent OpenLab CDS (version 2.x)
Contents:
In the following procedure, you will find steps to create a multipoint ESTD calibration method with OpenLab CDS 2.X.
Steps to follow:
1. Load the Data
a. From Data...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Chromatographic peak integration is a critical part of accurate and reproducible quantitative data analysis. The integrator type and the integration parameters...
This Information Applies To: Agilent 6200/6400/6500 Series LC/MS Systems
Issue
Instructions on how to fill the calibrant bottle on 6200/6400/6500 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal.
Issue:
Installing the Ion Transfer Capillary after cleaning or replacement. For instructions for installing an ion capillary...
This Information Applies To: AriaMx Real-time PCR System
Issue
The saturation level is unique for each optical module after the offset of calibration factor and background calibration. The FAM, ROX, HEX, CY3 & CY5 optical modules will saturate at...
This Information Applies To: Agilent LC Systems
Issue
While it is possible to combine modules from different HPLC series such as 1100, 1200, 1260 or 1290 series to create a functioning LC system, there are some important topics to consider.
...
Fixes for the "RPC Server Unavailable" Error
Multiple Results
This Information Applies To: Agilent OpenLab CDS
Issue
When launching the instrument Acquisition screen/instrument session, there is an "RPC Server Unavailable" error.
Resolution
Accessing the Services App (Windows)
There are two ways to...
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...