In detail, you can follow below link to resolve this type of problem.
https://community.agilent.com/technical/gc/w/wiki/7889/troubleshooting-an-fid-not-igniting
Hopefully, problem will solve..
Our Ultivo LC/TQ fails autotune immediately citing a Nozzle Fault. The log suggests the associated voltage is out of optimal range. Funnily enough, the system passes check-tune without any issue! The check-tune report shows the voltage perfectly matching…
I'm trying to install Openlab CDS 2.7 on Windows 10. When running the system preparation tool, everything passes test except the Ports Check -configuration: 'workstation ' and it says FAIL. I tried to run the recheck and repair, but it still fails. Any…
The MS column exits into vacuum. The FID column exits to atmospheric pressure.
Same carrier gas, column, oven temperature, inlet pressure results in different holdup times. These examples are using the Pressure Flow Calculator available here GC Calculators…
I am looking to set up in line sampling on a GC/FID (6850A, G2630A) with a capillary column. I have found sample valves listed for 6850 series GCs (e.g. G2668A), but the part description specifies it is for G2630B, so I take it that this is incompatible…
Dear Community Member,
I have facing some issue in ELECTRONIC PNEUMATIC CONTROLLER (EPC) of GAS CHROMATOGRPAH (7890B) The EPC Module has not give the Set Flow rate for AIR Flow, as we have give the Set Point of Air 350 ml/min, but the observed flow…
After some burner head cleaning, I reassembled my FAAS 240FS and now I can't get the burner head to light. Some details:
I was running some "dirty" samples with the nitrous burner head that plugged up the sample capillary and started to block the…
I found that our syringe plunger failed to withdraw sample. By replacing with a new syringe, the problem solved. So the sensitivity issue is resolved. thank you very much for your tip. However, we have come across another issue - unusual features in the…
I was experiencing ghost peaks in my water blank shots so I decided to do some maintenance. This included a new S/SL liner and septum, removing the first inch or two of the column, FID disassembly and ultrasonic cleaning of the jet, and reassembly. Now…
This Information Applies To: Agilent OpenLab CDS (version 2.x)
Contents:
In the following procedure, you will find steps to create a multipoint ESTD calibration method with OpenLab CDS 2.X.
Steps to follow:
1. Load the Data
a. From Data...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Chromatographic peak integration is a critical part of accurate and reproducible quantitative data analysis. The integrator type and the integration parameters...
This Information Applies To: Agilent 6200/6400/6500 Series LC/MS Systems
Issue
Instructions on how to fill the calibrant bottle on 6200/6400/6500 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal.
Issue:
Installing the Ion Transfer Capillary after cleaning or replacement. For instructions for installing an ion capillary...
This Information Applies To: AriaMx Real-time PCR System
Issue
The saturation level is unique for each optical module after the offset of calibration factor and background calibration. The FAM, ROX, HEX, CY3 & CY5 optical modules will saturate at...
This Information Applies To: Agilent LC Systems
Issue
While it is possible to combine modules from different HPLC series such as 1100, 1200, 1260 or 1290 series to create a functioning LC system, there are some important topics to consider.
...
Fixes for the "RPC Server Unavailable" Error
Multiple Results
This Information Applies To: Agilent OpenLab CDS
Issue
When launching the instrument Acquisition screen/instrument session, there is an "RPC Server Unavailable" error.
Resolution
Accessing the Services App (Windows)
There are two ways to...
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...