Hello, we were not able to tune the instrument at all. There was so much noise at low mass that it fails the initial quad coarse mass calibration. We think it is PEG contamination, possibly also PPG, but a number of masses correspond with sodiated PEG…
Morning, You are correct. I am running OpenLab CDS ChemStation. Rev code = C.01.04 [35]. Intelligent Reporting product version A.01.04.122. The system suitability issue is that I'm only getting the TCD satistical results. The FID result are not printing…
The tune evaluation criteria are benchmarks that GCMS instruments typically pass.
"Designed for" and "works with" are two different things. The tune evaluation was created before the Extractor Source and High Efficiency Source. These ion sources get…
Hello Lars, Thanks for your reply. Unfortunately, there is no flow meter meter installed. So you are saying that, in your case without stopping gas flow before GC injection, you are only getting 1-2% deviation in FID response? If possible could you explain…
Hey Ryan, try the following. Normally, the valve command failed is coming as a result of the position not found. Overtightened screws are a typical result if you have done maintenance before (happened to me the first time...). Tighten the screws each…
I have a G4226A autosampler with a recurring error message. Movement of needle into seat failed [EE 4714, 3204]
This error started after the autosampler had been repaired by a field engineer. The main board had to be replaced; the computer was unable…
Hi I have a very basic question, please correct me if I am wrong. I am using GC 7820 with FID detector. Flow , Pressure everything was set by another technician before I started. I know for Back Detector everything is what is set by the Technician in…
I think that, with this version of the software, there are configuration files stored in the "instrument number folder", e.g. C:\Chem32\n I was going to suggest that you try to delete/rename the config.reg file, having closed all instances of Chemstation…
This Information Applies To: Agilent GC Systems
Issue
Excessive baseline noise can be introduced at different points including sample preparation, sample introduction, separation, and the detector. The excessive background can cause reduced signal...
This Information Applies To: Agilent GC Systems
Issue
Baseline instability that is not reproducible across multiple runs can be introduced at different points including sample introduction, separation, and the detector. The baseline instability...
This Information Applies To: Agilent GC Systems
Issue
Peak fronting is present in a chromatography peak when it has an excessive asymmetry with a leading edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
This Information Applies To: Agilent GC Systems
Issue
A shift in retention time can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
A change in peak size can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
Peak splitting is when a single compound is shown in the chromatogram as two peaks usually unresolved, or one of the peaks is a shoulder.
Other chromatographic problems are identified in Basic...
This Information Applies To: Agilent GC Systems
Issue
This test isolates the point of contamination to the sample introduction system, which includes the gas supply, gas supply lines, and the sample inlet. It does not include the syringe or autosampler...
This Information Applies To: Agilent GC systems
Issue
Peak tailing is present in a chromatography peak when it has an excessive asymmetry with a trailing edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
T his Information Applies To: Agilent 8890/8860/7890/7820/6850/6890 GC Systems with TCD (Thermal Conductivity Detector)
Issue
Problems observed with thermal conductivity detector (TCD) results can have different underlying causes.
Resolution...
This Information Applies To: All GCs, 6890, 6850, 7890, 7820, 8890/8860, Intuvo 9000
Issue:
This article is a troubleshooting guide for when the Flame Ionization Detector (FID) does not ignite or the flame keeps going out.
Cause:
If the FID...