My knowledge of GCs is extremely limited. Currently we analyze for n-pentane only. The program was already set-up when I started working here.
Yes, an FID is present
1. Sampling vessel type unknown at this time.
2. I am expecting the range to be…
While removing a column from an Agilent mass spec 5977B the column broke off and I can't figure out how to remove it. I'm using MassHunter version 10.1.64.1 (12/15/2021) but not actually using the mass spec but only the FID on the back. If I start a sequence…
I have a chemist who uses GC/MS and has been experiencing issues with running samples and when he connects to the workstation with GC/MS via VNC Viewer it causes the samples to fail and throw errors such as, "Cannon open file D:\MassHunter\GCMS\1\simulate…
I have the flex metal G3188-27501 ferrules. when it comes to the Inlet, the ferrules fit alright and I can tighten them onto the column. When it comes to the FID port, the ferrule is too long and I can't screw in the column to the outlet. If I really…
hi all,
we have ICP-MS 7800 and getting error 1445. The content of the error is as follows:
"1445, Error: Plasma gas flow rate is too low." We can't ignite plasma.
Gas valves and gas line have been checked and there is no problem.
Does anyone…
Hello!
I am inquiring about a Turbo-V 3K-T High Vacuum Turbo Pump which unfortunately failed due to a bearing problem. I would like to receive information and advice on the following issues:
1. Is a repair kit available for the Turbo-V 3K-T pump?…
How do I convert the Peak Area (pA*s) measurements in a GC-FID lab report into mass/weight percent of components for analysed crude oil samples?
How do I characterise the n-paraffins and estimate the single carbon number (SCN) distribution from the…
I'm running a GC(7890A) / MS(5975C) with MassHunter Acquisition software. I automate much of my data analysis in Python by exporting the GC signal (FID) to .csv, and then exporting the MS signal using 'Export 3-D Data...' in MSD Productivity Chemstation…
Hi all :) For he experts here! I did my yearly maintenance (new gold seal, liner, column end cut to inlet and FID, new gas filters, ...). But since then, everytime there's a temperature change in the GC, the signal will show a sudden bump and then it…
This Information Applies To: Agilent GC Systems
Issue
Excessive baseline noise can be introduced at different points including sample preparation, sample introduction, separation, and the detector. The excessive background can cause reduced signal...
This Information Applies To: Agilent GC Systems
Issue
Baseline instability that is not reproducible across multiple runs can be introduced at different points including sample introduction, separation, and the detector. The baseline instability...
This Information Applies To: Agilent GC Systems
Issue
Peak fronting is present in a chromatography peak when it has an excessive asymmetry with a leading edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
This Information Applies To: Agilent GC Systems
Issue
A shift in retention time can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
A change in peak size can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
Peak splitting is when a single compound is shown in the chromatogram as two peaks usually unresolved, or one of the peaks is a shoulder.
Other chromatographic problems are identified in Basic...
This Information Applies To: Agilent GC Systems
Issue
This test isolates the point of contamination to the sample introduction system, which includes the gas supply, gas supply lines, and the sample inlet. It does not include the syringe or autosampler...
This Information Applies To: Agilent GC systems
Issue
Peak tailing is present in a chromatography peak when it has an excessive asymmetry with a trailing edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
T his Information Applies To: Agilent 8890/8860/7890/7820/6850/6890 GC Systems with TCD (Thermal Conductivity Detector)
Issue
Problems observed with thermal conductivity detector (TCD) results can have different underlying causes.
Resolution...
This Information Applies To: All GCs, 6890, 6850, 7890, 7820, 8890/8860, Intuvo 9000
Issue:
This article is a troubleshooting guide for when the Flame Ionization Detector (FID) does not ignite or the flame keeps going out.
Cause:
If the FID...