Hi azrael, The FID is not a pressurized detector so there is no pressure test. You may wish to explore our GC Fundamentals series on our website. See Below for a link Fundamentals of Gas Chromatography (GC) - Part 1 | Agilent Regards James
Hi Mike,
Thanks for the reply but i have run the instrument performance test it was ok.
Customer is using quarts cuvettes.
another issue we found when running wavelength accuracy and precision run from the validation, it missing one or two wavelength…
We have a 7890B that was configured with an MSD but is being reconfigured for a different analysis. It is now running an FID/TCD method, and the aux detector has been disconnected and unconfigured. The MS/Aux Det button on the GC keyboard says no aux…
Hello,
I am having an issue getting the system pressure test to pass. I have referred to the manual and followed all the steps, and have checked for any leaks (there are no visible leaks) and the leak test on the system is also passing - yet the pressure…
Hi This morning the check Tune failed. After adjusting MS1, the tune passed with warnings. Then I decided to autotune. It went through many of the steps until "Enhanced" failed. I am not sure what this step is. Not easy to find any documentation. Can…
When Air gap is 0.2 and the flow rate is 2.1 ml/min then the peak area found 287 by FID but when the air gap is 0 and flow rate is 1.47 ml/min then the area reduced to 141. Where analysis performed by Autosampler.
I think we do this at my lab but not with a valve. We use a plot column and anayze headspace above a water sample. We test for methane ethane ethene and propane useing an FID. The integrated gastight syringe with a valve in it from Fisher helps. We use…
Hello everyone
I have 3 error messages from the Agilent infinity ii 1260 SFC Multi sampler:
1- Metering device Movement Failed ( EE25444.0) 2- Taking needle From park station failed ( EE25105.201 ) 3- Axis did not reach its target position in time…
Using OpenLab EZChrom A.04.1.0.0 with a 6890N GC-FID this error occurs
The IS dept have looked into this and have commented that the systems log mentions that the instance has reached its maximum size of 32MB. We have been running the same system…
Hi, I have the same problem as well. We are using LC 1220 Infinity series. We tried flushing the system with isopropanol for 10 minutes just in case the bubbles are present. However, this does not solve the problem. The pump failed to get ready within…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...