Hello, I would appreciate any help possible with this question. I have an Ultivo LC/TQ and it is having the problem with autotuning. It fails due to spray stability. Due to this I am thinking it might be the nebulizer? I take it out and see good spray;…
It's OK.
I don't know if the valve is included in the pump or somewhere else.
If the valve fails, we'll have to use our Agilent maintenance/repair contract to clean the system... ;)
We don't know what is in your water samples, but on a CP-Wax 57 CB benzene and isopropanol are eluting very close to ethanol, just in front of it.
You can find examples of applications of alcoholic beverages on Wax 57 (all types) in Scanview ( (+) Software…
Hello mckenzie.stevens ,
Did this error occur when attempting to work with the FID data? I've not seen this exact error, but it is possible to receive similar errors when having a spectrum tool selected and trying to work with non-MS data. If you then…
Hello, Software: OpenLab Chemstation edition C.01.09 Software driver version: B.01.07.3[6648] Instrument: GC 7890B, Headspace 7697A I am using the above instrumentation and software. When I attempt to create a sequence/edit sequence table, I get the following…
My Agilent 5110v ICP-OES returns an error message "Timeout in plasma controller state operations (State 7)" or "ErrorNumber_PLASMA_CTRL_BASE_STATE_TIMEOUT" and the plasma fails to lit. Please, what how do I fix the error? I have cleaned the torch, and…
Hello. We have a 2- dimension gc/fid/ms 8890/5977C with a masshunter software. Our aim is to quantify molecular markers (e.g. 1,3,5-Tri-tert - Butylbenzene) used in gasoil to trace fraud. For quantitation we use a sim method (Quantification sim 231 and…
Hello,
we are using a G1312B binary pump (1260 Infinity) and had the error message: Fan Failed
After acknowledging the error message I can turn on the module as usual and it is working quite fine.
Nonetheless, I am not sure whether the fan is working…
Hello,
Thank you for the response. I created MH_meida folder in C drive and also enabled .NET 3,5. But I received error message again after trying to install qual 10.0. Any suggestions would be much appreciated. Thank you.
here is the error log…
Hello ljones031 ,
I would suggest copying the installation files to a folder on the local hard drive and then disconnecting any external drives before attempting installation. Most MassHunter programs will try to install to a D: drive it if is found…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...