the abundance of ion 69. I rechecked the source and it doesn't look dirty. then I did an autotune it stopped on the width mass axis of the second quadrupole.
Finally, after 2 or 3 more attempts, I ended up completing the autotune with an abundance of…
Hi all,
I am currently troubleshooting a leaky 1260 infinity II HPLC-SFC-ELSD and want to carry out a leak test in the utility program, but i could not find a clear, detailed description on how to do this. Could anyone direct me to the correct resource…
Hi!
I still need help yes, please!
- On the machines (GC system and Injector) it just says HP6890 (see photos attached)
- The PC we employ is an old Windows XP running one, that was used to run the GC-FID before we want to control it with the serial…
Hi, I would suggest to test the same without column installed to the FID. If problem looks similar check for leaks at the FID gas lines and clean the FID. If not clean the inlet and replace the split vent line and filter. Maybe try a new column.
BR…
Hi there, I noticed recently that the ECD back signal on Agilent GC 7890 (using it for trace gas analysis) is oddly spiking (while the FID is a straight, consistent line). It never used to do this. I just recently changed the inlet septum, could this…
Hi Community
I have an Issue on one of our GC-FIDs 6890N. I have large Peak Tailing, especially on the back of my chromatogramm:
What i already did:
- New Column
- New Septa/liner
- New Gold Plate
- Cleaned Inlet and Detector
- Re…
I have a Cary 3500 and running Cary UV Workstation Software 1.2 and Windows 10
I downloaded the new Cary UV Workstation Software 1.3 via the Agilent SubscribeNet.
first I ran the systemPreparationTool.exe
That finished without issues.
Then I ran…
*The system and method are given at the bottom of this post*
I am working with an Agilent 8860 operating a DB-624 UI (30m x 0.25mm x 1.4um) column with nitrogen carrier gas and split inlet (20:1). The system was shut down for approximately 1 year, and…
Any special procedures to prepare for cross-country shipment a 7890B with SS, PP inlets, heated valve oven, and TCD-FID? Also a 7697A with 100-vial tray?
Turning off the systems on Friday night that need to be ready to go on Monday morning is not recommended. It can take quite some time for a GC/MS to come back up to operational after being shut down. Even cooling the temperatures all down and then heating…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...