Good day . i have another issue to my 8890. after replacing the fused silica in transfer line. tha air flow in FID is suddenly shutting down. then i try the detector diagnostic in the system it said test failed and need to replace the jet.
after replacing…
Hello,
this look like your plasma is not align with the cones. For the EM to failed it's difficult. You have to check for noise when it's doing it and if the counts are low when it's using mass 80. You can try to tune EM with mass 37 if you know where…
Hello,
I am currently developing a residual solvent analysis method by Gas chromatography equipped with a flame ionization detector. My sample is an API with a phosphate salt attached. One of the residual solvents of interest is triethylamine. When…
8/7/19
Hello,
I have had a fair amount of success with posted questions in this forum, so here is another one. I am interested in knowing more about whether the flame ionization detector I have equipped on my HP/Agilent 6890 GC is the correct detector…
Try to ignite the plasma, without fixing the shield plate. Due to poor quality of argon gas or leak on gas line, reflected power will be above the limit and prevent the plasma sustain. Sometimes, the plasma sensor fiber optics tip is damaged, needs to…
When I need information about detectors I use the following books:
Raymond P. W. Scott "Chromatographic Detectors - Design, Function, and Operation", Chromatographic Science Series Volume 73, Marcel Dekker, New York (1996). ISBN 0-8247-9779-5.
Raymond…
We have a lot of 1260s and 1290s in our lab, and as part of our sustainability initiatives are looking for ways to reduce our energy usage. Currently, all the instruments are left on (standby), and most of them also have the lamps on when not in use.…
Hi Guys,
I have a GC that does not seperate natural gas(maily C1 and C2 with small traces of C3+), it comes as almost one peak, and for condensate (C3+) it seperates C6+, and does not seperate C3÷C5,
I Have,
1: Readjusted the split ratio Many Many…
Hello Inês,
Typically we use the Performance report as a general health report of the instrument. Changing plasma parameters may cause the test to fail, unless you correct the limits. Moving the sample depth will decrease sensitivity and can increase…
Hello
I'm trying to setup report to have values in column "PASS/FAIL" green or red depends on result.
Can I do it as conditional formatting for column "PASS/FAIL" to mark FAIL as red based on text?
This column "PASS/FAIL" is custom field and…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...