As title states.
Instrument: #1 shows "GCMS9"
Instrument #2: should show "GC16"
However on the quant report, only Instrument #1 is accurate, the quant reports on #2 read HP G1530A
I've checked msdchem.ini and InstName is defined properly…
Hello,
Did you apply update 06 before upgrade? It´s necessary.
This update 06 fixes this flaw in version 07, after this action you update to version 08.
Regards,
Rafael Pinto
The Cary 60 UV-Vis and its nearly endless supply of accessories
We’ve written before about the many accolades of the powerful yet accessible Cary 60 UV-Vis and its highly flexible software. This instrument’s popularity seemingly knows no bounds and…
Hello,
I am expeirencing the same issue after having to reload E.02.02.1431. The quant report prints as one job and the chromatogram and the spectra reports (I'm printing a detailed report) print as a second job.
I've done as ron_tackett mentioned…
Instability in the anode voltage will cause baseline problems in your detector signal. For example, if the lamp doesn't light properly, the voltage will reset and you will see periodic changes in the baseline. I have seen old lamps sometimes produce odd…
I can't seem to get our new instrument to pass an EPA DFTPP tune for method 525.2. We recently got an instrument with the hydroinert source and I have only gotten a couple of passing tunes but nothing that is repeatable. I have tried manual tuning myself…
Yes! I checked the line too as according to the instructions (+) How to Disassemble and Assemble the HES (High Efficiency Source) - Articles - GC/MS Portal - Agilent Community
I will take a picture when I have them out next time. Thank you so much for…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...