• Created : 
  • Modified : 
  • Category :  Agilent Knowledge Portal
  • Entry Type :  Article
  • Product Type :  Analytical LC Systems
  • Component :  LC Pumps
  • Product Name :  1220 infinity II LC System 1260 Infinity II Bio-Inert LC System 1260 Infinity II LC System 1260 Infinity II Prime Bio LC System 1260 Infinity LC System 1260 Infinity II Prime LC System 1290 Infinity II Bio LC System 1290 Infinity II LC System 1290 Infinity LC System
  • Task :  Troubleshooting
Related Articles

  • Troubleshooting "Vacuum Limit Not Reached" Error in Agilent LC Pumps

    This Information Applies To: Agilent G1311B/C, G7110B, G7111A/B, G7112B, and G7120A Pumps and Agilent G7122A, G4225A, G1379A/B, and G1322A Degassers Issue The error message "Vacuum Limit Not Reached" will appear if the degasser does not reach a preset limit (default value is 100 mbar) in a predefined time window (default 8 minutes after powering on the module). This may happen for many reasons. One reason may be due to the condensation of vapors from volatile organic solvents. The vapors...

  • What Components determine Gradient Composition and Flow Accuracy in Binary and Quaternary Pumps

    This Information Applies To: Agilent Binary and Quaternary LC Pumps Issue When performing a gradient analysis, it’s important to know what component determines composition if it becomes necessary to troubleshoot chromatographic inconsistencies. Those inconsistencies can manifest themselves as peak retention time shifts (late or early peaks) and merged or missing peaks. Troubleshooting strategy depends on the pump type being used. This article will describe how binary and quaternary pumps create...

  • How to Troubleshoot Low Pressure or No Flow/Solvent Coming Out of 1100/1200 Series Isocratic/Quaternary/Binary Pumps

    This Information Applies To: Agilent 1100/1200 Series G1310A Isocratic Pump, G1311A Quaternary Pump, and G1312A/B Binary Pump modules Issue This article shows different options to troubleshoot low pressure or no flow issues in 1100/1200 series Isocratic/Quaternary/Binary pumps. Items Required Open-end wrench 14 mm (p/n 8710–1924 ) Open-end wrench 1/4 - 5/16 inch (p/n 8710–0510 ) Pair of Tweezers Steps to follow The following steps will guide you to find out which part is causing...

  • General Recommendations for Using an Agilent RID

    This Information Applies To: Agilent Refractive Index Detectors, G1362A and G7162A/B. Issue: The RID is sensitive to its environment and can experience stability problems when exposed to contamination, vibrations, mechanical shocks, or changes in temperature or pressure. Resolution: Considerations on the general set-up: To avoid cross-talk between different solvent channels, preferably use an isocratic pump when operating a RID. If it is not possible to use an isocratic pump, consider...

  • Good Practices for Use of the Multi-Channel Gradient Valve in Agilent Quaternary Pump Modules

    This Information Applies To: Agilent Quaternary Pumps with Multichannel Gradient Valves Issue: The correct use and maintenance of multichannel gradient valves (MCGVs) in Agilent Quaternary Pump modules will prevent blockage or damage of this assembly. It will help ensure the MCGV functions correctly and reliably. Resolution : Warning : Use the proper PPE and precautions when handling hot water and solvents. General: Before operating the quaternary pump, flush the...

Turning Off the Built-in Degasser Within a Pump Module

Answer

This Information Applies To: Agilent LC Pumps with built-in Degasser

Issue

If the built-in degasser is not working and gives an error on power-on, the pump will be in error mode, and therefore no injections can be made. The user may wish to disable [or enable] the degasser, especially in an isocratic run, to be able to still use the pump while the degasser is repaired.

This article details how to disable the degasser.

Steps to follow

  1. Launch Lab Advisor and connect to the Instrument. 
  2. Go to Instrument Control > [Pump model] > Controls > Control > Degasser Controls and select Degasser > Off. (See Figure 1)

Note:  If you turn off the degasser, and cycle power the pump, it will revert to being back on so will need to repeat the preceding steps each time.


Figure 1
Figure 1. Built-in degasser Lab Advisor control

 

  
Tips: For additional information on degasser troubleshooting, see: Troubleshooting "Vacuum Limit Not Reached" Error in Agilent LC Pumps
Was this helpful?
Contact Agilent Support

Still Need Assistance?

Contact Agilent Support >
Privacy Statement
Terms of Use
Contact Us
Site Help