• Created : 
  • Modified : 
  • Category :  Agilent Knowledge Portal
  • Entry Type :  Article
  • Product Type :  GC/MS Systems
  • Component :  GC/MS Triple Quadrupole
  • Product Name :  7000 Series Triple Quadrupole GC/MS 7010 Series Triple Quadrupole GC/MS
  • Task :  Installation Operation
Related Articles

  • Gathering Diagnostics Log Files from the 8890/8860/Intuvo 9000 GC Systems Using the Browser Interface

    This Information Applies To: Agilent 8890/8860/Intuvo 9000 GC Systems Issue When you are working on troubleshooting an Agilent GC system with an Agilent support representative, you may need to provide the GC diagnostics logs. This article shows how to get the files from the browser interface of the 8890, 8860 and Intuvo 9000 GC Systems. Requirements A PC that is on the same network as the GC. Tip: You can also gather the logs directly from the Agilent Software. See the following...

  • How to Set up Communication Between Agilent 5000 Series ICP-OES Instruments and Agilent ICP Expert Software

    This Information Applies To: Agilent 5000 ICP-OES Series and Agilent ICP Expert Software Issue How to connect Agilent 5000 series ICP-OES systems to Agilent ICP Expert software via LAN Steps to Follow How to connect Agilent 5000 series ICP-OES instruments to Agilent ICP-Expert software using the standard configuration of a static IP address The Agilent 5000 series ICP-OES uses a LAN communication between the computer and instrument. Caution : Any changes to default network...

  • How to Use the Browser Interface for 8890 and 8860 GC Systems

    This Information Applies To: Agilent 8890 and 8860 GC Systems Issue: The Browser Interface of the 8890 and 8860 GC systems, provides for instrument setup and control, as well as the ability to run the instrument stand-alone (without a connected data system). The Browser Interface provides many of the same functions as the touchscreen. Topics How-to connect to the Browser Interface How-to access stored run data How-to control Browser Interface access How-to use the Help function...

  • How To Use and Configure Early Maintenance Feedback (EMF) on the Agilent 8890/8860 GC Systems

    This Information Applies To: Agilent 8890/8860 GC Systems Issue Early Maintenance Feedback is a useful feature on Agilent GC Systems and software that allows a user to monitor the maintenance needed on their GC. This feature allows for users to get a reminder that maintenance is due on their instrument before it causes a chromatography or even a hardware issue. If you are changing parts on your GC on a scheduled basis, either based on a certain passing of time or a specific number of injections...

  • Gathering GC Diagnostics Log Files Using the Agilent Acquisition Software

    Multiple Results
    This Information Applies To: Agilent OpenLab CDS, OpenLab ChemStation, OpenLab EZChrom, MassHunter Acquisition Software for GC/MS Systems, and Agilent 7890/7820/8890/8860/Intuvo 9000 GC Systems Issue When you are working on troubleshooting an Agilent...

How to Modify the IP Address of a GC/QQQ System with the Web User Interface

Answer

This Information Applies To: Agilent 7000C/7000D/7010B triple quadrupole GC/MS

Issue

The GC firmware does not support LVDS communications with the 7000C/7000D/7010B GC/TQ, so you must use the Web User Interface (WUI) to configure the MS detector network settings.

Steps to Follow

  1. Press the MS On/Off switch to start the instrument.

  2. From the controlling PC Web browser, type the current instrument IP address and press enter (See Figure 1). The WUI Main Menu page will be displayed. The default IP address is 192.168.254.12; but other IP addresses could be configured in the instrument.


    Address bar. 
    Figure 1. Instrument IP address into a PC Web browser address bar

  3. From the main menu page, click the Edit NetConfig button (Figure 2).


    Main menu.
    Figure 2. Main menu

  4. Scroll down to the Edit NetConfig (QQQ network configuration) section. Type the GC IP Address in the DCOMM Partner IP Address if your GC supports DCOMM. TheGC must be an Agilent 7890B or 7890A+ with the latest firmware for DCOMM support (Figure 3)


    Edit NetConfig section.
    Figure 3. Edit NetConfig section

  5. Enter the IP Address, Gateway IPA, and Subnet Mask for the Triple Quadruple.

  6. Click the Submit button to assign this IP address to the Triple Quadruple.

     

      
    Tips: Attach a label to the Triple Quadrupole recording the NetConfig Parameters, or store them in a known location.

  7. Close the browser page when you are done.

  8. From the PC desktop, run the Agilent GC/MS Instrument Configuration program (Figure 4)


    Agilent GC/MS Instrument Configuration desktop icon.
    Figure 4. Agilent GC/MS Instrument Configuration desktop icon

  9. In the GC/MS Instrument Configuration program, edit the triple quadrupole IP address using the new parameters. (Figure 5, Figure 6)


    Instrument Configuration.
    Figure 5. Instrument Configuration


    Setting the IP address.
    Figure 6. Setting the IP address.
     

 
Learn more on how to effectively operate your Agilent GC/MS MassHunter software: 
Agilent 7000 or 7010 Triple Quadrupole GC/MS with MassHunter Workstation e-learning course available from Agilent education

 

 

Was this helpful?
Privacy Statement
Terms of Use
Contact Us
Site Help