Hi Dr. Know
Here is some of the information you have requested. Please let me know if you need any further info.
How is your system configured? FID detector using helium as carrier gas, nitrogen as makeup gas.
Which phases are the two columns…
Hello from Kazakhstan,
Very interesting theme.
I also have some issues with flow method correction and some questions.
1) We use Excel CFT calculator. So how much pressure we should put on calculator, when using SCD detector with FID? As calculator…
Yes, the MassHunter software uses a conversion factor and reports in "counts" instead of hertz for uECD data. The conversion factor is 7680.
The 7680 multiplier also applies to other GC based detectors such as FIDs and TCDs.
Hi
I am pretty new to GCMS, so may need extra details on how to do things you suggest
I attached a picture of the set up of our gc system, so I can explain better. We recently installed a guard column using 30 cm piece of FS Deactivated 0.250 mm(Agilent…
Hi,
We are using MassHunter 10.0.368 to collect data on a GC-FID (7890B). The software will randomly crash (the software shuts down with no information in the logbook) during a sequence, usually after 100+ samples. We have updated MassHunter to version…
What you describe with the washes happening, but a delay when pulling up the actual sample for injection sounds like something about the GC is not in a ready state and the GC is waiting for a part of the GC to become ready. In this case you describe it…
First of all, thank you for posting publicly, I had not noticed this interface feature of MassHunter Quant, it looks very useful.
Were you able to get it working in 11.1?
If you're allowed to share your "IScriptable" folder, I would be very interested…
The test can be done with or without flow cell. Like I said, the last test didn't look awfully bad to me (remember, a failed test in LabAdvisor doesn't necessarily indicate a real problem or even hardware failure).
Check your environmental conditions…
I have the same problem when the instrument is switched to work at a negative mode. do you think my Medusa power supply also failed? what is the part#? Is G1969-65360 the right part #?
Thanks
Hydrogen (H2) is the simplest and most abundant element in the universe. Since, it only occurs naturally on Earth when combined with other elements it must be produced from other sources. It can be produced without a carbon footprint from variety of sources…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...