Hi, I think it would be a good idea to upload your startup tune report in order to help you better.
Also I think you could take advantage of reading this post: https://community.agilent.com/technical/atomic-spec/f/forum/470/icp-ms-manual-tuning
Hello,
So, file based workstations store the full path to the methods in the sequences. If there is any change between the systems in the project path this is the expected behavior if you copy a sequence. If you open the sequence, browse out and find…
Hello guys,
I recently discovered, that it is possible to change your font properties in the injection list via shortcut (ctrl + b for "bold" and so on..).
Therefore I wanted to ask you, if there is some code for changing font types for CCF outputs…
Hi Mai,
Thank you for reaching out to Agilent technical support.
Please check:
if the data file you are trying to open was generated using TapeStation security module as that can be one reason for the file not to open and error out.
If anyone…
Thank you for confirming what I had found. I figured that there wasn't a way around the time reference/ISTD link. Mostly, I am surprised that MassHunter is limited in a way that Chemstations/OpenLab are not.
Hello jeremy_lai ,
Available graphics options for reports can be found on the Graphics settings tab in the Report Method editor. From what I can find, the Qualifier graphic does not have any specific display options available. The only ones that apply…
Hello bertinettis ,
I apologize for the delayed response.
There is an option in quant to enable pre-set peak annotations in the Add-Ins from the Tools menu/ribbon.
These will then appear in the Compound Information window. Once a peak has been…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...