Hi mr.white, I already did several upgrades from OpenLAB EZChrom to OpenLAB 2.x. let me write some pros/cons: Pros - fully virtualized, support server 2019 and Windows 10 - easy upgrade (same integrator, raw data can be copied and opened, method imported…
We have recently replaced the ESI needle on our Agilent 6100 LC-MS. All is well with the flow, but we are not able to tune our instrument. Last week, the tune looked fine, but since replacing the needle the peaks (118, 622, 922) are not found and we get…
Can Someone help me in converting below logical statements to IR. Statement IF Assay>99 And Assay<101 ,Then "Pass" Otherwise Display "Fail" Syntax I used =Iif(99<Assay<101,"Pass","Fail") But results I am getting as below Always Pass Thanks & Regards Rajesh…
Hi Erik, This depends on the version of G2070AA or BA. The below may help. The Autostart Macro failed, error# 999 occurs on startup of the Chemstation if the Initial Screen Window Size is set to “Icon” in the Configuration editor. In the PCS section of…
Last week we vented and powered off our Agilent 6650 iFunnel QTOF. When we tried to turn it on and pump down from mass hunter software (I think B 09), the rough pump ran at the beginning, but just after 10 min, then it automatically stops. After a couple…
We have backup generation, and we also recently put all of our instruments on a full-pass UPS system (Weissco Power - www.weisscopower.com) All power to each instrument goes through the UPS system. The nice thing about the system we have is that the power…
Hello and thanks for your quick answer! I would like to come back to my starting question: if i use macros i can not find the changes from the chemstation in the documentation. For example (one question from above): In Version C.01.10 the Sequence is…
Hi azrael, Thanks for the clarification. If the ground is not functioning at the outlet, the metal of the GC cannot be grounded. This means anything that was touching the metal chassis of the GC could have been subjected to the full line voltage - lots…
This Information Applies To: All Agilent Gas Chromatographs, 6890, 6850, 7890, 7820, 8890, and 8860.
Issue:
A quick reference guide on the capillary column installation for the GC.
Inlets
Detectors
Split/splitless inlet Purged...
How to Add a GC Instrument in Agilent OpenLab CDS (Ver 2.x)
Multiple Results
This Information Applies To: Agilent OpenLab CDS (Ver 2.x)
Content:
The following procedure shows how to add a GC instrument in OpenLab CDS (Ver 2.x).
Steps to Follow:
1. Open OpenLab CDS Control Panel, in the Instruments interface, select...
This Information Applies To: Agilent Intuvo 9000, 8860, 8890, 7890A/B, 7820A, 6890, 6850 GC Systems with Split/Splitless, or Multimode Inlets.
Issue:
This article describes how to replace the inlet septum for Split/Splitless and multimode inlets...
This Information Applies To: Agilent GC Systems
Issue
The data rate determines the number of sampling points across the chromatographic peak and the sample background. The data rate is based on the width of the analyte speak (in minutes) and the...
This Information Applies To: Agilent GC Systems
Issue
Excessive baseline noise can be introduced at different points including sample preparation, sample introduction, separation, and the detector. The excessive background can cause reduced signal...
This Information Applies To: Agilent GC Systems
Issue
Baseline instability that is not reproducible across multiple runs can be introduced at different points including sample introduction, separation, and the detector. The baseline instability...
This Information Applies To: Agilent GC Systems
Issue
Peak fronting is present in a chromatography peak when it has an excessive asymmetry with a leading edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
This Information Applies To: Agilent GC Systems
Issue
A shift in retention time can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
A change in peak size can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
Peak splitting is when a single compound is shown in the chromatogram as two peaks usually unresolved, or one of the peaks is a shoulder.
Other chromatographic problems are identified in Basic...