Agilent Community
Agilent Community
  • User
  • Site
  • Search the Community
  • User
Gas Chromatography Portal
  • Agilent Knowledge Portal
Gas Chromatography Portal
GC Articles How to Align the Agilent 7693A GC Injector
  • GC Articles
  • GC Videos
  • GC Forum
  • More
  • Cancel

Browse the Agilent Knowledge Portal

  • Chromatography
    • Gas Chromatography
    • Liquid Chromatography
  • More
  • Cancel
  • GC/MS
  • More
  • Cancel
  • Spectroscopy
    • Atomic Absorption
    • ICP-OES
  • More
  • Cancel
  • Automated Electrophoresis
  • More
  • Cancel
  • Software and Informatics
    • OpenLab CDS
    • MassHunter
  • More
  • Cancel
  • -Gas Chromatography
    • +GC Operation
    • -GC Maintenance
      • +GC Systems
      • -GC Samplers
        • Removing and Installing a Syringe on the Agilent 7693A Autosampler
        • How to Align the Agilent 7693A GC Injector
        • Changing the Turret of the 7693A Automatic Liquid Sampler
        • Replacing the Syringe Carriage Assembly in the Agilent 7693A Automatic Liquid Sampler
        • How to Align the Agilent 7693A ALS Sample Tray
        • How to Calibrate the Agilent 7693A Sample Tray
        • How to Align the Agilent 7683B GC Injector
        • Replacing a Broken Transfer Line on 7697A Headspace Sampler
    • +GC Troubleshooting
    • +GC Best Practices

How to Align the Agilent 7693A GC Injector

Created by Carlos Vargas Carlos Vargas over 2 years ago | Last modified by Carlos Vargas Carlos Vargas 1 month ago

This Information Applies To: Agilent 7693 Automatic Liquid Sampler


Issue:

Only use this alignment procedure if the injector hardware configuration has changed or if the Align Mode light comes on.

Agilent does not recommend performing this procedure unless the Align Mode light turns on, or if Agilent Support requests it to be performed. The injector is factory-aligned before shipment and it is not necessary to align it after changing injectors.


Steps to follow

  1. Remove all vials from the turret.

  2. Open the injector door, remove the syringe, and close the injector door.

  3. Use a long, narrow object to press the recessed Alignment button above the indicator lights. (Figure 1.)  Avoid contact with anything behind or around the button inside the recessed hole. Let the injector move freely. (Figure 2)


    Figure 1. LEDs and Alignment button position.
    1. Align mode LED, 2. Fault LED, 3. Ready LED, 4. Alignment button



    Figure 2. Aligning the injector.


  4. The orange Align Mode light is on until the following alignment procedure has been completed:

    1. The turret rotates to verify that the syringe was removed, then rotates to determine what type of turret is installed.

    2. The syringe carriage moves all the way down, homes, then moves back up again.

    3. The syringe carriage steps down until it touches the turret. This sets its position relative to the turret.

    4. The syringe carriage moves down and the turret rotates to set its position relative to the syringe carriage position.

      If any of these steps fail, the process will halt and the fault light will shine. If it halts at step b, confirm that the turret is installed correctly and press the Alignment button again. If it fails again, unplug the injector, reconnect it, and try one more time before obtaining Agilent service.

  5. When the injector stops and the green Ready Light is on, the calibration is finished.

  6. Open the injector door, install the syringe, and close the injector door.

 Tip 
Learn more how to effectively maintain your Agilent 7693A Automatic Liquid Sampler:
SI-7693-1100s - Agilent 7693A ALS Basic and Advanced Operation and Maintenance e-learning available from Agilent education.
  • Automated Liquid Sampler
  • 7693A
  • Best practices
  • GC Sample Introduction
  • Share
  • History
  • More
  • Cancel
Was this helpful?
  • Yes
  • No
Thank you for your feedback!

Agilent Community Feedback

Agilent Community Feedback

×
We are glad this was helpful! We are sorry this was not helpful. If you still need assistance please create a community post or contact support. To help us improve, please provide any additional feedback. For full details of how we will treat your information, please view our privacy policy.
Submit Cancel
Submit Cancel

Contact Agilent Support

 Still Need Assistance?

 Contact Agilent Support >

Related
Recommended for you
Privacy Statement
Terms of Use
Contact Us
Site Help