• ICP-MS MassHunter Batch Templates in Compliance Mode with Protect Local Data = ON

    Open video

    carlos_vargas
    last modified by carlos_vargas
  • Importing and Exporting ICP-MS MassHunter Batches in Compliance Mode

    Open video

    carlos_vargas
    last modified by carlos_vargas
  • Report Designer for ICP-MS MassHunter in Compliance Mode

    Open video

    carlos_vargas
    last modified by carlos_vargas
  • ICP-OES 5110 Instrument Calibration with an Organic Set-up

    Hi all - I am brand new to running ICP-OES and have a question about the instrument Calibration function. My instrument is set up to run organic samples and we do not have torches or spray chamber to hand aqueous samp...
    lbrothers
    last modified by lbrothers
  • High Concentration calculations on Na when the signal intensity for the sample is higher than the blank?

    Hi all -   I am very new the ICP-OES analysis and I am very confused by the values that the Agilent software is calculating. I prepare samples with a 100 fold dilution (I am running in organic solvent not aqueou...
    lbrothers
    last modified by lbrothers
  • Sodium counts are increasing.  How to I manage/control this

    Hello,   I am running a 7800 ICP MS for EPA 200.8 method.  I have noticed the pass number of months the sodium counts during my warm-up and shut down are running in the 50,000 to almost 100,000 counts. ...
    jackiec
    last modified by jackiec
  • What are the best practice to run Mercury on ICPMS

    Hello It has been observed sometime that while working on ICPMS, not getting good linearity of mercury. SO, what are the best practice follow to prepare the mercury standards (calibration points) and rinsing solutio...
    vinajain
    last modified by vinajain
  • Analysis of 0.1M H3PO4 and 0.5N NaOH extracts by 7800

    Hello, we perform extractables testing at my lab and we have an upcoming study of single-use thermoplastic elastomer tubing which will be extracted in the following solvents: water, 0.1M H3PO4 and 0.5N NaOH. I am obvi...
    srains
    last modified by srains
  • IntelliQuant V7.5 - Difficulties with Na & K

    Hi,   I am using an Agilent 5100 ICP-OES with ICP-Expert V7.5. I am having some issues getting IntelliQuant to give me back a good estimate for Na, K and Mg but mainly Na.   I've recently updated the calib...
    agricult
    last modified by agricult
  • ICP – EOS 725 Radial

    Hello, I need help, what model number HVAC in ICP – EOS 725 Radial, I don't found in manual. HVAC - heating, ventilation and air conditioning systems. This system cooling control hf block. &...
    a.fedulova
    last modified by a.fedulova
  • Dllinstall Error2: Cannot load library

    Greetings,   I am running a 7700 ICP-MS with MassHunter version B.01.01 on Vista with Service Pack 1, Firmware: Smartcard:3.3.23 Build #34 and Z80: C.02.00 Build #029.   I am unable to boot the instrument ...
    tgluodenis
    last modified by tgluodenis
  • Liquid Sample Introduction Pre-Run Check

    Hi, Just out of curiosity would someone be able to answer the following question in relation to an Agilent 7900 ICP-MS. I know the correct way to secure the peri-pump tubing to the peristaltic pump i.e. drain line on...
    edta
    last modified by edta
  • Replacement of Penning Guage

    Greetings All,   I have a 7700 ICP-MS and on startup received the error #1122 Penning Gauge malfunction.  I did try to eliminate any dust in the gauge by loosening the vent value to introduce air then resta...
    tgluodenis
    last modified by tgluodenis
  • ICP-MS Mass Hunter - Error Standart Lens Tune

    ICP-MS Mass Hunter 4.1. I can not Starup Standart Lens Tune! The message appears "Failed to add Startup/Hardware tasks to Queue; Enter path for batch folder". As usual (my Batchs)- everything works.
    dp44
    last modified by dp44
  • Na pollution

    Can't reduce of Na. Agilent 7900 (pump - off, spray carrier gas - off) reads 1,000,000 cps! Burner, spray chambers and 1 cone is a cleaned. Changing (up) the carrier gas - incre...
    dp44
    created by dp44
  • Gas Dilution HMI (ICP-MS).

    I use Agilent 7900 and gas dilution HMI-8 and HMI-25. The device automatically changes the Power and Sample depth. I expect to get a sample dilution of 8 and 25 times. This is not happening. Actually dilution is less....
    dp44
    last modified by dp44
  • Troubleshooting Failed Plasma Ignition for Agilent 5000 Series ICP-OES

    Agilent Support Insights   This Information Applies To: 5100, 5110, 5800, and 5900 ICP-OES instruments   Issue: ICP-OES plasma ignition may fail due to various reasons, but often the user can resolve th...
    tmcsweeney
    last modified by tmcsweeney
  • AA Nickel absorption issues

    I have a AA 240FS.  I am having trouble getting a good absorption signal for one metal Nickel.  My other metals seem okay. Is there something I can do to optimize for Nickel absorption. I co not even get a g...
    hfujimoto
    last modified by hfujimoto
  • Troubleshooting and Maintenance of AA Systems: Part 2B- Flame Optimization

    Agilent Support Insights   This Information Applies To: All Agilent Flame AA Systems- 55B, 240FS, 280FS    Issue: After cleaning and re-installing the flame atomic absorption system components...
    tmcsweeney
    last modified by tharville
  • Motor Mount for 700 ICP OES Peri Pump

    Because it is 4pm on a Friday, the rubber supports that attach the drive motor to the peri-pump have fell apart on my 700 ICP OES. Would anyone happen to have replacement order number for the supports for the mot...
    jsharun
    last modified by jsharun